156-315.82 sample questions

Question 1

Your data center will run two R82 ElasticXL Clusters. To save switch ports, a network engineer plans to connect the Sync ports of both clusters to the same dedicated Sync VLAN.

What is correct?

Accepted Answer

This is not supported; each ElasticXL Cluster needs its own Layer 2 domain for Sync.

Answer

It works if the second cluster's Sync network uses a subnet other than 192.0.2.0/24.

Answer

It works because each cluster encrypts its Sync traffic with its own key.

Answer

It works if every member of the second cluster joins with site-id 2.

Question 2

In an R82 Management High Availability deployment, what is the primary function of the 'Full Sync' operation compared to the standard delta sync?

Accepted Answer

It copies the entire database from the Active to the Standby server, overwriting all data on the Standby.

Answer

It forces the Standby server to become Active and syncs back to the original Active server.

Answer

It merges the databases of both servers, preserving unique objects from each.

Answer

It synchronizes only the configuration files and ICA certificates.

Question 3

A financial institution requires strict audit trails for their firewall policy changes. They are using an R82 Management High Availability setup.

Which of the following statements is TRUE regarding the synchronization of audit logs between the Active and Standby Management Servers?

Accepted Answer

Audit logs are synchronized automatically as part of the database synchronization process.

Answer

Audit logs must be manually exported and imported to the Standby server.

Answer

Only traffic logs are synchronized; audit logs are excluded to save bandwidth.

Answer

Audit logs are only stored locally on the server where the change was made.

Question 4

While troubleshooting a synchronization issue between two R82 Management Servers, you decide to use the CLI to check the detailed status of the HA peers.

Which command provides the MOST comprehensive status of the Management HA synchronization state?

Accepted Answer

mgmt_cli show ha-status

Answer

fwm ha_print

Answer

cphaprob stat

Answer

cp_mgmt_ha -s

Question 5

Your organization is performing a disaster recovery test. The primary R82 Security Management Server has been shut down. You need to promote the Standby server to Active to resume administrative operations.

Which of the following actions achieves this?

Accepted Answer

Use the SmartConsole (connected to the Standby server) or API to set the server to 'Active'.

Answer

Run 'cpstop' and 'cpstart' on the Standby server.

Answer

Modify the 'ha_active' registry key in the Gaia Portal.

Answer

The Standby server will automatically detect the failure and promote itself within 60 seconds.

Question 6

A multinational corporation uses Updatable Objects in their R82 Access Control Policy to allow traffic to Microsoft 365 services. The security team notices that the policy installation on the gateways takes a long time due to frequent updates.

How does the R82 architecture optimize the handling of Updatable Objects to mitigate this issue?

Accepted Answer

The gateway downloads updates directly from the Check Point cloud, bypassing the need for a policy installation for object content updates.

Answer

Traffic to Updatable Objects is automatically bypassed from Deep Packet Inspection.

Answer

The Management Server caches the updates and pushes a mini-policy every 5 minutes.

Answer

Updatable Objects are converted to static network groups during policy compilation to speed up enforcement.

Question 7

You are configuring Manual NAT rules on an R82 Security Gateway. You want to ensure that your Manual NAT rules are evaluated BEFORE the Automatic NAT rules generated by the object properties.

Where must these Manual NAT rules be placed in the Rule Base?

Accepted Answer

In the 'NAT' tab, above the section labeled 'Automatic Generated Rules'.

Answer

In the 'Global Properties' NAT section.

Answer

Below the 'Automatic Generated Rules' section.

Answer

Manual NAT rules always take precedence regardless of position.

Question 8

An administrator needs to manage a Security Gateway at a remote branch office. The Management Server has a private IP address and sits behind a corporate firewall that statically translates it to a public IP address.

Which configuration lets the remote Gateway send logs and status updates to the NATed Management Server?

Accepted Answer

Define the Management Server object with its private IP and add the public NATed IP in the 'NAT' properties of the Management Server object.

Answer

Configure a manual static NAT rule on the remote gateway.

Answer

Use the 'masters' file on the remote gateway to hardcode the private IP of the Management Server.

Answer

Enable 'Global NAT' in the Global Properties.

Free 156-315.82 sample questions

Your data center will run two R82 ElasticXL Clusters. To save switch ports, a network engineer plans to connect the Sync ports of both clusters to the same dedicated Sync VLAN. What is correct?

In an R82 Management High Availability deployment, what is the primary function of the 'Full Sync' operation compared to the standard delta sync?

A financial institution requires strict audit trails for their firewall policy changes. They are using an R82 Management High Availability setup. Which of the following statements is TRUE regarding the synchronization of audit logs between the Active and Standby Management Servers?

While troubleshooting a synchronization issue between two R82 Management Servers, you decide to use the CLI to check the detailed status of the HA peers. Which command provides the MOST comprehensive status of the Management HA synchronization state?

Your organization is performing a disaster recovery test. The primary R82 Security Management Server has been shut down. You need to promote the Standby server to Active to resume administrative operations. Which of the following actions achieves this?

You are configuring Manual NAT rules on an R82 Security Gateway. You want to ensure that your Manual NAT rules are evaluated BEFORE the Automatic NAT rules generated by the object properties. Where must these Manual NAT rules be placed in the Rule Base?

9 more free samples are waiting